 |
C13S, C13SH
| Dim | C13S(H) | |
| Center height | mm | 400,500 |
| Distance between centres | mm | 1500, 2000, 3000, 3150, 4400, 5000, 6200 |
| Width of bed | mm | 540 |
| Max. turning diameter | ||
| - over the bed | mm | 800, 1000 |
| - over the cross slide | mm | 540, 740 |
| - in gap | mm | 1050,1250 |
| Max. weight of the workpiece | Kg | 3150 |
| Spindle nose | No.11/15 DIN | |
| Spindle bore | mm | 136/153 |
| Max. torque | Nm | 4000 |
| Main motor power | kW | 15(18,5) |
| Spindle speeds numbers | 24 | |
| Spindle speed range | rpm-1 | 6,3-850 |
| Range of longitudinal feeds | mm/rev. | 0,13-30,72 |
| Range of transversal feeds | mm/rev. | 0.04-9.216 |
| Number of threads | ||
| - range of metric threads | mm | 1-240 |
| - range of inch threads | TPI | 60-1/4 |
| - range of module threads | Module | 0.5-120 |
| - range of DP threads | DP | 120-1/2 |
| Traverse slide maximum stoke | mm | 420, 520 |
| Upper slide maximum stroke | mm | 200 |
| Diameter of tail axle of free saddle | mm | 110 (120) |
| Cone hole of tail axle | MT | 6 |
| Max quill travel | mm | 280 |
| Machine length by DBC 1500 | mm | 3535 |
| Machine length by DBC 2000 | mm | 4035 |
| Machine length by DBC 3000 | mm | 5035 |
| Machine length by DBC 4400 | mm | 6180 |
| Machine length by DBC 5000 | mm | 7035 |
| Machine length by DBC 6200 | mm | 7980 |
| Machine width | mm | 1400 |
| Machine height | mm | 1600 |
| Machine weight by DBC 1500 | kg | 4600/+500 |
| Machine weight by DBC 2000 | kg | 5100/+500 |
| Machine weight by DBC 3000 | kg | 5700/+500 |
| Machine weight by DBC 4400 | kg | 6500/+500 |
| Machine weight by DBC 5000 | kg | 6900/+500 |
| Machine weight by DBC 6200 | kg | 7900/+500 |
| STANDARD EQUIPMENT CE: 1.El. equipment complete; 2.Electric control panel “Telemecanique”; 3.Cooling system with pump; 4. Low voltage machine lightning; 5.Rapid traverse device; 6.Redaction sleeve MT.6/MT.5; 7. Redaction sleeve MT.6/MT.4; 8. Dead center MT.6; 9. Dead center MT.5; 10. Dead center MT.4; 11. Toolholder shield; 12. Chuck shield; 13. Safety shield rear whole machine length; 14.Action for the screen for the universal; 15.Safety hand wheel; 16.Safety clutch handle; 17.Stop of the rear sadle; 18.Safety chip pan; 19. Lead shaft and screw protection; 20. Emergency stop button; 21.Safety machine lamp; 22.Lock of the quadrant for the lamp; 23.Sings according the “CE”; 24. Gears changeover; 25. Operation manual. EXTRA EQUIPMENT: 1.Taper turning attachment; 2.Fixed steady with range ø 280-530 mm; 3.Fixed steady with range ø 30-280 mm; 4.Traveling steady with range ø30-200mm; 5. Fixed steady with range ø 530-730 mm; 6. Fixed steady with range ø 100-360 mm;7. Stand for fixed steady 8. Thread chasing dial; 9. 4-jaw independent chuck ø 760 (960) mm; 10. Jawless face plate ø 760 (960) mm; 11. 1 – position longitudinal stop limited; 12. 3-jaw universal chuck U 315 (400,500); 13. Flange for universal chuck U 315(400,500,630); 14. Drive plate; 15. Set of turning dogs; 16. Live center; 17. Drill chuck P 20 with shank MT.6; 18. Foot stop pedal. NOTE: ZGMM JSC reserves the right to make constructive and technical machinechanges without warning. ZGMM JSC can change the color of the machines by client's wish. |